Digital Peripherals / SDM-SIO4A
SDM-SIO4A Four-Channel Serial I/O Module
Serial I/O Expansion for Dataloggers
weather applications water applications energy applications gas flux and turbulence applications infrastructure applications soil applications

Overview

The SDM-SIO4A is a serial I/O expansion module for Campbell Scientific data loggers. It is designed to add four additional and individually configurable and addressable RS-232, RS-422, or RS-485 (half- or full-duplex) serial ports to an SDM-capable data logger for the purposes of interfacing with intelligent sensors, actuators, or displays. Up to three SDM-SIO4A modules can be connected to a single data logger SDM port. The SDM-SIO4A channels behave much like a native data logger serial port and use the same familiar serial I/O commands. The SDM-SIO4A is transient and surge protected to IEC61000-4-5 level 4 on the serial port interfaces, avoiding the need for separate transient protection in most applications.

Note: The SDM-SIO4A is not a direct replacement for the SDM-SIO4. The SDM-SIO4A consists of four SDM-SIO1A modules in a single package. Consequently, the SDM-SIO4A is a good replacement for up to four SDM-SIO1 modules or as an alternative to the SDM-SIO1A.


Read More

Benefits and Features

  • Easy and compact method to add up to 12 additional serial ports to an SDM-capable Campbell Scientific data logger
  • Fully compliant with the RS-232, RS-422, and RS-485 (half- and full-duplex) standards
  • Can buffer large amounts of serial sensor data between datalogger processing events
  • Supports data logger terminal "talk-through" mode, facilitating serial device testing and diagnostics
  • Includes transient and surge protection on the serial port interface, eliminating the need for separate transient protection
  • Low idle power consumption, which is ideal for battery-powered stations

Images

glam view
glam view
glam view
front tilt view
front view
front view
front tilt view
back view
left view
right view
top view
bottom view

Detailed Description

The SDM-SIO4A connects to multiple remote serial devices using industry-standard hardware that can be set to true RS-232, RS-485, or RS-422 signal levels. When operating in RS-232 mode, the channel also supports hardware handshaking. RS-422 mode is functionally the same as RS-485 mode, except the connection is limited to a point-to-point system. Connections and programming for RS-422 are otherwise identical to RS-485.

The SDM-SIO4A will accept serial data up to 6143 bytes and store it in its buffer. This allows remote equipment to transmit large amounts of data without needing to stop other processes in the data logger.

Up to three SDM-SIO4A modules can be connected to a single data logger using the SDM port, allowing a user to connect 12 different serial devices to a data logger with ease. This is in addition to any connections made to the data loggers via other serial ports.

The SDM Jumper Wire Kit (pn 32505) connects up to four SDMs to the data logger. This kit is recommended when multiple SDMs are connected to one data logger or for extremely short distances between the SDM and data logger. The CABLE5CBL-L cable is recommended for connecting a single SDM to the data logger, and for longer distances between the SDM and data logger.


Specifications

Function Expands the number of serial devices that can communicate with a data logger.
Number of Channels 4
Supported Data Rates 300, 1200, 2400, 4800, 9600, 19200, 38400, 57600, and 115200 bits/s
Supported Modes of Operation
  • RS-232 (full duplex and receive only)
  • RS-485 (half and full duplex)
  • RS-422 (half and full duplex)
  • Hardware CTS/RTS flow control is supported in RS-232 mode. The handshaking lines can also be used as general purpose I/O lines.
Supported Data Format
  • In 7 bit mode with no parity, the user must ensure that the characters received by the SDM-SIO4A have a delay of at least one bit period or greater between them. This does not affect any other configuration and does not affect transmissions out of the SDM-SIO4A.
  • 8, 7 bit data size; none, odd, or even parity; one or two stops bits
Auto Baud Rate Detection Auto baud rate detection is NOT supported.
PakBus Communications Use of the serial port for general PakBus communications is not currently supported.
Voltage
  • Power supply +12 V connection
  • 7 V (minimum)
  • 12 V (nominal)
  • 30 V (maximum)
Operating Temperature -40° to +70°C (standard)
Humidity 0% to 95% (non-condensing) standard
Mounting Holes Two spaced 17.78 cm (7 in.) apart
Mounting Clips Optional DIN rail mounting clips are available, which can be fitted to the base of the case.
EMC Compliance The SDM-SIO4A has been tested and shown to comply with IEC 61326. The device incorporates transient and surge protection that is designed to meet IEC61000-4-5, level 4, providing the device is adequately grounded.
Dimensions 6.4 x 15.45 x 2.2 cm (2.51 x 6.09 x 0.86 in.) excluding mounting tabs

Buffer Sizes

-NOTE- Both transmit and receive buffers are fill and discard type. That is, after the buffers become full, no new information is accepted, and all further data is discarded until space is made when the data logger requests data from the SDM-SIO4A.
Transmit Buffer Size 767 bytes (buffer from the data logger to the sensor)
Receive Buffer Size 6143 bytes (buffer from the sensor to the data logger)

Current Consumption

Active Current 9.6 to 11.7 mA (depending on transmit mode and connections made)
Standby Current
  • 110 µA nominal, 400 µA (applies at max temperatures only)
  • 500 µA nominal, 1200 µA (applies at max temperatures only)

Compatibility

Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.

Dataloggers

Product Compatible Note
CR1000 (retired)
CR1000X
CR200X (retired)
CR211X (retired)
CR216X (retired)
CR300
CR3000 (retired) On the CR3000, SDMs are connected to the ports labeled SDM-C1, SDM-C2, and SDM-C3.
CR310
CR350
CR5000 (retired) The CR5000 is compatible with the SDM-SIO4A, but the operating system must be OS 6 or higher. On the CR5000, SDMs are connected to the ports labeled SDM-C1, SDM-C2, and SDM-C3.
CR6
CR800 (retired)
CR850 (retired)
CR9000X (retired) The CR9000X's operating system must be OS 6 or higher.

Mounting Equipment

Product Compatible Note
ENC10/12
ENC12/14
ENC14/16

Miscellaneous

Product Compatible Note
ENC10/12R
ENC16/18

Additional Compatibility Information

Data Logger Considerations

The SDM-SIO4A does NOT support auto baud rate detection nor the use of the serial port for general PakBus communications.

Enclosure Considerations

The SDM-SIO4A requires a desiccated, non-condensing environment; a Campbell Scientific enclosure is recommended. The SDM-SIO4A has built-in keyhole flanges for mounting to the backplates of Campbell Scientific enclosures.



Downloads

SDM-SIO1A / SDM-SIO4A OS v.3.0 (401 KB) 10-01-2024

Current firmware for the SDM-SIO1A and SDM-SIO4A.

View Revision History

Case Studies

Croatia: Modernization of a Countrywide Weather Observation Network
Overview The National Weather Observation Network in Croatia, led by the Croatian Meteorological and Hydrological Service......read more

Listed Under

Replacement Part for the following products:

Privacy Policy Update

We've updated our privacy policy.  Learn More