Testing the calibration of your rain gauge is a simple process. But as you know, it’s also easy to introduce problems, such as incorporating simulated data as real data. In this article, we’ll review a useful feature that automates the testing process and can help you avoid errors.
The process of programming or configuring a data logger is normally only done once at the beginning of an application. Yet, the data logger is often used on regular site visits to verify proper operation and calibration of the connected sensors, as well as to test communications and several other site-service tasks. These tools are built into the free Hydro-Link™ software interface to help you save time and increase efficiency in your site-service activities.
Verifying the operation of a rain gauge is one of the site-service activities that is often done on a regular schedule. When you use the Hydro-Link software interface with a CR300 or CR310 datalogger, testing the calibration of your rain gauge is a simple process that resolves many common issues.
Applications that use rain gauges often require the rain gauge calibration to be verified at regular intervals. You may perform this calibration check after completing other tasks, such as cleaning and checking the level of your rain gauge. You may, like others, check the calibration by pouring a set amount of water into the rain gauge at a set flow rate to simulate rainfall at a specific rate per hour. This should cause the data logger to measure a fixed amount of rainfall. Any difference from the expected amount would be an error.
This type of test is simple, based on the current procedures commonly used. Unfortunately, without using Hydro-Link, you may experience some of the following:
The tool in Hydro-Link automates the test and resolves all the issues we’ve mentioned above. The following sections will help you use Hydro-Link for your rain gauge calibration.
When you use the generic rain gauge option in Hydro-Link, the following screen is displayed on the dashboard for the rain gauge:
|The top value shows the current rain accumulation. You can edit this value so that the rain value can be preset to a known value.
|You use all the other options on the dashboard to verify the rain gauge calibration. The three options with buttons may require your input. The other options show test results.
Before you start the test, you need to enter the expected amount of simulated rainfall. Click the button for Cal_Check_Expected_Rainfall to enter the expected rainfall amount:
A commonly used size of calibration beaker holds 946 milliliters of water, which is equal to 1.15 inches of rain in an eight-inch rain gauge. If you are using inches for your rainfall unit of measurement, enter 1.15 for the expected rainfall. The following shows how this value was determined:
For an 8 in. rain gauge
To start the test, click the toggle button to change Cal_Check from false to true.
After the test is started, the data logger automatically performs several actions described below:
|The main Rain_Accum variable is automatically disconnected internally from the input, so this value will not increase during the test. If a scan or measurement process happens while the test is running, this unaltered value will be used without the simulated rainfall affecting it.
|For the test run time, a timer is set to 15 minutes. This will decrement to 0, and the test will automatically stop running. If the test will take longer than 15 minutes, you can easily change this time to the desired amount needed.
|The rain gauge input is automatically connected to this test accumulator. As you pour water into the gauge to simulate rainfall, the Cal_Check_Rainfall variable increases, indicating how much simulated rainfall has been measured.
|The error percentage value decreases as water flows into the gauge. After the water stops flowing, this value shows the total error as a percentage.
|Using the time from the first tip to the last tip, it is easy for the user to calculate the rate of rainfall.
After the test is running, you can start the flow of simulated rainfall into the gauge at the desired rate. Typically, the container holding the water has an outlet fitting that controls the water flow. This flow represents a specific rate of rain—for example, four inches of rain per hour.
Tip: To have accurate results, ensure that all the water in the container is poured into the rain gauge before the test is complete.
As the water flows into the rain gauge, the percentage error decreases until the measured value is the same as the expected rainfall. At that point, the error percentage is 0.00.
After all the water in the container has passed through the rain gauge, the error value and accumulation value stop changing.
After all the water has passed through the gauge, you can manually stop the test by clicking the toggle button for Cal_Check—just like you did when you started the test. Alternatively, you can just let the timer expire.
After the test is complete, all the results are stored in a table file named “RainfallSimHist” that you can retrieve at any time. The table has an entry for each time the calibration check was used. The following example table has two lines of data at the bottom, which show that the test was run twice:
"TOA5","HLink","CR300","1123","CR310.Std.08.01","","","RainfallSimHist" "TIMESTAMP","RECORD","Cal_Check_TimeFromFirst_ToLastTip","Cal_Check_Rainfall","Cal_Check_Expected_Rainfall","Cal_Check_Error_Percent" "TS","RN","","","","%" "","","Smp","Smp","Smp","Smp" "2018-08-24 17:53:45",0,"00:14:28",1.13,1.13,1.74 "2019-01-22 22:22:15",1,"00:14:42",1.12,1.12,2.60
The end results show a 1.74% error in August of 2018 (2018-08-24) and a 2.60% error in January of 2019 (2019-01-22).
After the test is complete, the system returns to recording rainfall normally.
If you need data for simulated rainfall intensity, you can calculate the intensity per hour using this equation:
Rain intensity/h = (3600 s/h) / test time (s) * Rainfall
If you look at the data from the last test in the table file above, the time from the first tip to the last tip was 14 minutes and 42 seconds (14:42), which is 882 seconds. The measured rainfall was 1.12 inches. Using these values in the equation, we can calculate the rainfall intensity:
Rain Intensity/h = (3600 s/h) / 882 s * 1.12 in. = 4.57 in./h
Tipping bucket rain gauges, by their nature, require regular servicing and calibration checks. Each organization sets the interval for how often a gauge must be checked and decides which error limits are considered acceptable.
For example, you might choose to use guidelines such as these:
The rain gauge calibration check tool is one of many tools available in the Hydro-Link software. These tools are provided to make your site visits easier and to increase the confidence on all operational aspects at the site. To get started using Hydro-Link, refer to these resources:
Please contact a Campbell Scientific sales or support representative for more information about rain gauge calibration or other Hydro-Link options and field-service tools.